Difference between revisions of "Br46 v1"
From DIDEAS Wiki
m |
m |
||
| Line 25: | Line 25: | ||
*buck converter : http://cds.linear.com/docs/Datasheet/3470fc.pdf | *buck converter : http://cds.linear.com/docs/Datasheet/3470fc.pdf | ||
*Nfet for power control : http://www.diodes.com/datasheets/ds30928.pdf | *Nfet for power control : http://www.diodes.com/datasheets/ds30928.pdf | ||
| + | *key rx : http://www.linxtechnologies.com/Documents/RXM-xxx-LR_Data_Guide.pdf | ||
| + | |||
*samtech connector : | *samtech connector : | ||
**http://www.samtec.com/documents/webfiles/pdf/mptc-RA_MPSC-RA.PDF | **http://www.samtec.com/documents/webfiles/pdf/mptc-RA_MPSC-RA.PDF | ||
**http://www.samtec.com/documents/webfiles/cpdf/MPSC-XX-XX-XX-01-XX-X-RA-XX-MKT.pdf | **http://www.samtec.com/documents/webfiles/cpdf/MPSC-XX-XX-XX-01-XX-X-RA-XX-MKT.pdf | ||
| − | + | ==logic== | |
| + | *http://www.diodes.com/datasheets/74LVCE1G08.pdf | ||
| + | *http://www.st.com/stonline/books/pdf/docs/5733.pdf | ||
==note== | ==note== | ||
*PSer2hb leaves IO pins as NC. Will need to add pullup/pulldown | *PSer2hb leaves IO pins as NC. Will need to add pullup/pulldown | ||
Revision as of 17:32, 15 October 2010
PF Users Navigation:
- PCB; Lifefix_users; Pf_users; benchtest_users; CalibFix Users; Hardware; Assembly ; iochan ;
- PCA : PCB ; AKENC SC/MC 218 ; FET 217 ; IMU219 ; Swifi ; Rev200_mods ; PCA Inventory
- Special Commands to the Ankle (PFCMD) : State Controller Commands; Motor Controller Commands; Python Examples; IMU Commands ;PFCMD_PY; Pf_calb_table_py; Virtual spring test; PF EEPROM
- DOC: Pf_users; Powerfoot Keyboard User Interface; Steps for Manual Tuning; "Dashboard" Program For Assisting with Tuning
- NEW (CEB) WIKI
- Torque Feedback Controller Guide
- garden12 ; emg_2009 ; Enc_2010 ; AKENC ; Kknee1 ; Br46_v1 gps1 ; lifefix ; battery ; loadwasher ; elecdog ; Brushless_control ; ceb_misc_prj ; pf_top_nav ; T
46 class 2
- http://www.blueradios.com/hardware_C46.htm
- http://www.blueradios.com/BR-C46AR.pdf
- http://www.blueradios.com/WML-C46A_R_Overall.pdf 17.6x11.8
40 class 1
- http://www.blueradios.com/hardware_C40.htm
- http://www.blueradios.com/WML-C40A_Overall.pdf 24x 13.x
- http://www.sparkfun.com/datasheets/Wireless/Bluetooth/BlueRadios_ATMP_Commands_Rev_3.5.1.1.0.pdf
mosfets
battery module
- dual cmp w/ref : http://cds.linear.com/docs/Datasheet/6700123fg.pdf
- Red/green LED : http://media.digikey.com/PDF/Data%20Sheets/Panasonic%20LEDs%20PDFs/LNJ115W87RA1.pdf
- 16V, 40ohm zener : http://www.diodes.com/datasheets/ds18004.pdf
- opamp : http://focus.ti.com/lit/ds/symlink/tl343.pdf
- LV reset : http://www.onsemi.com/pub_link/Collateral/NCP302-D.PDF (OBS)
- LV reset : http://www.micrel.com/_PDF/mic2775.pdf
- buck converter : http://cds.linear.com/docs/Datasheet/3470fc.pdf
- Nfet for power control : http://www.diodes.com/datasheets/ds30928.pdf
- key rx : http://www.linxtechnologies.com/Documents/RXM-xxx-LR_Data_Guide.pdf
- samtech connector :
logic
note
- PSer2hb leaves IO pins as NC. Will need to add pullup/pulldown
- Pser1 probably also leaves IO as NC.
- want to use FUP IP pin to disconnected on-board bluetooth Rx driver.
