Difference between revisions of "Upd 219 imu"
From DIDEAS Wiki
m |
m (→pinout (old SC Rev100->IMU) cable) |
||
Line 53: | Line 53: | ||
==pinout (old SC Rev100->IMU) cable== | ==pinout (old SC Rev100->IMU) cable== | ||
*12pin -> 10pin | *12pin -> 10pin | ||
− | *1 -> 1 | + | *1 -> 1 (VBAT) |
− | *2 -> NC | + | *2 -> NC |
− | *3 -> 4 | + | *3 -> 4 (SS) |
− | *4 -> | + | *4 -> 5 (SLK) |
− | *5 -> | + | *5 -> 6 (MOSI) |
− | *6 -> 7 | + | *6 -> 7 (MISO) |
− | *7 -> 9 | + | *7 -> 9 (SRVC) |
− | *8 -> 2 | + | *8 -> 2 (DEBUG) |
− | *9 -> 3 | + | *9 -> 3 (SCPWREN) |
*10 -> NC | *10 -> NC | ||
− | *11 -> 10 | + | *11 -> 10 (GND) |
*12 -> NC | *12 -> NC |
Revision as of 20:59, 26 June 2009
- PCA : SC/MC 218 FET 217 IMU 219 Swiffy Rev200_mods
PFMENU DOCS Aiw_hardware iochan AIW_assembly
Contents
IMU
1
- 6-26-09 : location CEB lab
- 6-23-09 : seems to be working
- 1-24-09 : boots and can reprogram - this will be the IMU development device.
- 1-24-09 : removed broken jumper wires from GND to R28. Shorted Q4 gate to ground.
- 1-24-09 : is missing pushbutton switch and is missing PB pad. Remain 3 pads don't seem to be enough to switch the system on.
2
- 6-23-09 : seems to be working with 'blue' cable w/red and black marks on connector
- 1-24-09 : was able to erase and reprogram.
- 1-24-09 : system is getting 3.3V w/push button - however, unable to program over protected segments
todo
- discuss with DY how to recover. Possibly sent back to UPD.
3
- 6-23-09 : seems to be working. appears to have been relabeled with #1 (despite the #3 appearing on two ICs.) removed label
- 1-24-09 : switching regulator gets voltage w/PB, however, 3.3V is unchanged.
todo
- replace switcher U7
IMU cables
- IMU cables with red wire are all subject to intermittent connections due to large wire size. use a small screw driver or xacto to press wires back into IDC slots.
pinout (new SC Rev200 -> IMU cable
- 12pin -> 10pin
- 1 -> 10
- 2 -> NC
- 3 -> 7
- 4 -> 6
- 5 -> 5
- 6 -> 4
- 7 -> 2
- 8 -> 9
- 9 -> 8
- 10 -> NC
- 11 -> 1
- 12 -> NC
pinout (old SC Rev100->IMU) cable
- 12pin -> 10pin
- 1 -> 1 (VBAT)
- 2 -> NC
- 3 -> 4 (SS)
- 4 -> 5 (SLK)
- 5 -> 6 (MOSI)
- 6 -> 7 (MISO)
- 7 -> 9 (SRVC)
- 8 -> 2 (DEBUG)
- 9 -> 3 (SCPWREN)
- 10 -> NC
- 11 -> 10 (GND)
- 12 -> NC