Difference between revisions of "Ankle-0406"
From DIDEAS Wiki
m |
m |
||
| (9 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | + | [[Biomechatronics_Documentation | Back to BM]] | |
| − | |||
| − | |||
| − | |||
| − | Greddy IMU pinout (top down / | + | [[GIMUAMP |GIMUAMP]] |
| + | [[QAKAMP | QAKAMP]] | ||
| + | [[AKBRK | AKBRK]] | ||
| + | |||
| + | ===First version IMU=== | ||
| + | *uses 2 axis ADXL311 linear acc | ||
| + | |||
| + | ===Current (Greddy) IMU=== | ||
| + | *[http://www.analog.com/en/prod/0,2877,ADXRS300,00.html ADXRS300 Rate Gyro] - needs clean 5V supply, output is independent of supply voltage. Has 14KHz switcher, should use separate power and signal ground. | ||
| + | |||
| + | *pack includes eval board from STM that contains [http://www.st.com/stonline/books/pdf/docs/10221.pdf LIS3L02AS4] (3 axis) with 110k output imp | ||
| + | *eval board is [http://www.st.com/stonline/prodpres/dedicate/mems/boards/boards.htm EK3L02AS4] - $52 from dig. Board contains volt reg and acc output buffers. [http://www.st.com/stonline/prodpres/dedicate/mems/boards/ev_kit/ek3l02as4/app_no.pdf APP NOTE] | ||
| + | |||
| + | LIS3L02 output is dependent on supply with zero acceleration at Vsup/2 (+- 10%). There doesn't seem to be a signal that corresponds to zero acceleration! | ||
| + | |||
| + | |||
| + | Greddy IMU pinout (top down / left to right) : | ||
Rate Gyro: 5 GND x y z | Rate Gyro: 5 GND x y z | ||
STM Acc : 5 GND yf, zf, xf, y, z, x | STM Acc : 5 GND yf, zf, xf, y, z, x | ||
| Line 10: | Line 23: | ||
* [http://memsense.com/downloads/datasheets/MAG3_SMT_Datasheet_revD1.pdf Commercial MAG3 IMU] | * [http://memsense.com/downloads/datasheets/MAG3_SMT_Datasheet_revD1.pdf Commercial MAG3 IMU] | ||
| + | |||
| + | * Strain gauge part # SG-7/1000-DY43 (or 93) from omega | ||
Latest revision as of 01:15, 20 April 2006
First version IMU
- uses 2 axis ADXL311 linear acc
Current (Greddy) IMU
- ADXRS300 Rate Gyro - needs clean 5V supply, output is independent of supply voltage. Has 14KHz switcher, should use separate power and signal ground.
- pack includes eval board from STM that contains LIS3L02AS4 (3 axis) with 110k output imp
- eval board is EK3L02AS4 - $52 from dig. Board contains volt reg and acc output buffers. APP NOTE
LIS3L02 output is dependent on supply with zero acceleration at Vsup/2 (+- 10%). There doesn't seem to be a signal that corresponds to zero acceleration!
Greddy IMU pinout (top down / left to right) : Rate Gyro: 5 GND x y z STM Acc : 5 GND yf, zf, xf, y, z, x xf,yf,zf are filtered and buffered
- Strain gauge part # SG-7/1000-DY43 (or 93) from omega
