Revision as of 00:49, 9 January 2009

PCB Hardware

• SCREWS
• side plates : 2.5mm
• K2 spring to ball nut / actuator : 2mm
• K3 spring : 7/64"
• front / back cover : 5/64"
• belt tension adjust : 50 mills

system

proto2

• 1-8-09 : brief test with Hugh and upright3 parameters. Delivered very little power, but could be tuning.
• 1-6-09 : Doesn't work with MCver CG6. Reinstalled CD6 from Dec 4. Probably should update to ~Dec 12 (tx demo)
• 12-31-08 : believed to be working from TX demo
• built with SC006, PB005. Problems with drive5 encoder.

• 12-4-08 : +20% series spring, with clamp in shows 2 detends (middle stiffness)
• 12-4-08 : Controller Upd_pcb#110-006 (has battery ECO)
• 12-1-08 : Controller Upd_pcb#110-009
• 12-1-08 : normal series spring with clamp in softest position
• Controller [Upd_pcb#110-006]]
• FET Upd_pcb#110-005
• Pyramid 5
• Drive6

proto1 (previously proto3)

• 1-8-09 : board set problems that caused oscilation? with initial mode 3 switch. Safety fet or anther failed.
• 1-6-09 : believe that power board is bad. will be updated with Upd_217_power_board#110-007
• 12-31-08 : needs more testing
• 12-31-08 : realized that PROTO1 plated was recently mounted onto ankle - thus PROTO3 became PROTO1
• 12-13-08 : SC and MC operational (respond to commands / LEDs flash). Power board not lit. filter, max PWM 30k.
• 12-12-08 : magic smoke escapes. (FET Upd_217_power_board#110-004
• 12-8-08 : operational with WOW pack
• 12-7-08 : +20% series spring, with clamp in stiffest position
• drive assembly #1
• Controller Upd_218_controller#110-205
• FET Upd_pcb#110-007 - expected
• BT 8b
• pyramid 8

pyramid

2

• 12-7-08 : found removed from proto3 with broken wire
• 12-3-08 : Installed on Proto3. SG gain needed to be reduced from 850 to 550.
• 12-1-08 : Q&D test, connector seems good

3

• 11-28-08 : May have been calibrated in OCT, current on test stand

4

• 12-1-08 : Q&D test, connector seems good

5

• 12-1-08 : operational on PROTO3. SG gain is 850.
• 11-28-08 : to be tested. May have been calibrated in OCT

8

• 12-7-08 : installed on proto3 without testing. apparently doesn't work.

motor / assembly

drive 1

• 12-8-08 : belt tension missing 1 of the 4 screws (head is broken)
• 11-28-08 : verified with +-1.5Amps

drive 2

drive 3

• 11-1-08 : motor frozen

drive 4

drive 5

• 12-6-08 : CEB tests drive, no response on any channel - all high - probably ground is open
• 12-5-08 : robert repairs encoder - by replacing with encoder from frozen motor
• 12-4-08 : problems with encoder, no pulses on channel b
• 11-28-08 : verified with +-1.5Amps

drive 6

• 12-6-08 : motor 6 pully has a problem. mounted incorrectly?
• 12-6-08 : added motor connectors

battery packs

bluetooth

• 100:001 : 8B (PDA -> right)
• 100:002 : 65 (PDA -> left)
• 100:003 : DF (PDA #4
• 100:004 ??: 8E (PDA #5)
•  ???:??? : 18 (PDA #3)