Difference between revisions of "Pf ui"
From DIDEAS Wiki
m |
m |
||
Line 1: | Line 1: | ||
=screen 0 (standard) = | =screen 0 (standard) = | ||
− | * | + | |
+ | |||
+ | *IKik : addjust Pff gain by +-5 / +- 1* | ||
+ | |||
+ | ==data fields== | ||
+ | <pre>RLXT (STD) E 0.0J MS:36 md:0 dT: 0 VB:24083 STP: 0 AA:+15.81 SK: 10.0 2.5 ES:645.0 5.0 LS:210.0 5.3 PCI:123 JM:1.0 35.0 PFF:64.0 E:3.00 0 TS_SP:-0.25 ENB:1 TC_TAU:50 LSP_D:30 []</pre> | ||
+ | * RLXT - the first field is the text string representing the present SM state | ||
+ | * (STD) - the 2nd field reports the present 'screen' | ||
+ | * E 0.0J - the 3rd field reports the energy per step averaged over the past few steps (tau=4 steps). Smaller values where subject gets power is better. Over 40J and the motor will likely overheat. | ||
+ | * MS:36 - the 4th field is the value of the MC statemachine state | ||
+ | * md:0 - the 5th fields is the MC controller mode (0 is shorted leads, 3=torque control, 6=voltage mode) | ||
+ | * dT 0 - IIR filtered motor temperature with tau = 20 steps | ||
+ | * VB:24083 - present supply voltage (mV). | ||
+ | * STP: 0 - the step counter. | ||
Revision as of 15:09, 13 August 2010
Contents
screen 0 (standard)
- IKik : addjust Pff gain by +-5 / +- 1*
data fields
RLXT (STD) E 0.0J MS:36 md:0 dT: 0 VB:24083 STP: 0 AA:+15.81 SK: 10.0 2.5 ES:645.0 5.0 LS:210.0 5.3 PCI:123 JM:1.0 35.0 PFF:64.0 E:3.00 0 TS_SP:-0.25 ENB:1 TC_TAU:50 LSP_D:30 []
- RLXT - the first field is the text string representing the present SM state
- (STD) - the 2nd field reports the present 'screen'
- E 0.0J - the 3rd field reports the energy per step averaged over the past few steps (tau=4 steps). Smaller values where subject gets power is better. Over 40J and the motor will likely overheat.
- MS:36 - the 4th field is the value of the MC statemachine state
- md:0 - the 5th fields is the MC controller mode (0 is shorted leads, 3=torque control, 6=voltage mode)
- dT 0 - IIR filtered motor temperature with tau = 20 steps
- VB:24083 - present supply voltage (mV).
- STP: 0 - the step counter.
screen 2 (random)
- az : adjust temperature threshold for Pff temperature rescaling (0 to turn off) (100 to 110 is a good value)
- sx : adjust temperature threshold to turn off robot (set 10 higher than above)
- DCdc : adjust the k3_bias by 100 / 10 mdeg (eg 0.1, 0.01 degrees)
- FVfv : adjust the k2_bias by 100 / 10 mdeg (eg 0.1, 0.01 degrees)
- GBgb : relaxed exit hardstop torque for exit to state 5 (by +-10 / 1)
- hn : relaxed exit maximum series torque allowed for pitch velocity exit condition
- jm : adjust pitch velocity threshold (200 is for HH, 300 is a good value)
- IKik : addjust Pff gain by +-5 / +- 1
- O : (the letter) zero the k2 and k3 bias values
- R : toggle relaxed mode enable
- < > : for experiment - (dis/en)able LS imped commands (to be removed)
screen 4 (sensors)
screen 9 (weight)
- q set weight to 100 lbs
- w set weight to 150 lbs
- e set weight to 200 lbs
- r set weight to 250 lbs
- AZ/ az : adjust weight by +-10 lbs / 1 lb
- +- : adjust weight by 0.1 lbs
- S E T to set the PCI, and other torque threshold parameters based on PCI