Difference between revisions of "POT4 PINOUT"
From DIDEAS Wiki
m |
|||
Line 1: | Line 1: | ||
− | + | [[POT4]] Header Pinouts | |
+ | |||
+ | =="POT" Input header (5 pin)== | ||
+ | ===Connection for a potentiometer=== | ||
+ | #REF+ : Positive reference output | ||
+ | #SIG : Potentiometer wiper "position" signal | ||
+ | #REG- : Negative reference output | ||
+ | #SHLD : Connect to the shield that encloses lead wires and potentiometer. Do not connect to the chassis or "GND" | ||
+ | |||
+ | #PKUP : Not used | ||
+ | |||
+ | ===Connection for a strain gauge bridge=== | ||
+ | |||
+ | #REF+ : Positive reference output, connect to "top" of bridge | ||
+ | #SIG : Amplifier positive input, connect to bridge signal (+) | ||
+ | #REG- : Negative reference output, connect to "bottom" of bridge | ||
+ | #SHLD : Connect to the shield that encloses lead wires and bridge. Do not connect to the chassis or "GND" | ||
+ | #PKUP : Amplifier negative input, connect to bridge signal (-) | ||
+ | |||
+ | |||
+ | =="POS-PWR" Power / signal header (5 pin)== | ||
+ | #+12 : Connect to a low noise +12V power supply | ||
+ | #P+ : Positive going differential "Position" output | ||
+ | #GND : Connect to | ||
+ | #P- : Negative going differential "Position" output | ||
+ | #-12 : Connect to a low noise -12V power supply | ||
+ | |||
+ | NOTES: | ||
+ | *P+ and P- are connected to low impedance drive though a 50 ohm resistor | ||
+ | *Capacitance of 1.1uF (typical) is placed across P+ / P- which forms 1st order lowpass filter with Fc=1.45KHz | ||
+ | *P+ and P- are fully differential and are NOT ground referenced. For single ended operation, at the receiving end, connect P- to the local ground. | ||
+ | |||
+ | |||
+ | =="Velocity" differentiated output header (2 pin)== | ||
+ | #V+ : Positive going "Velocity" output | ||
+ | #v- : Negative going "Velocity" output | ||
+ | |||
+ | NOTES: See preceding notes for P+/P- |
Revision as of 03:24, 2 June 2005
POT4 Header Pinouts
Contents
"POT" Input header (5 pin)
Connection for a potentiometer
- REF+ : Positive reference output
- SIG : Potentiometer wiper "position" signal
- REG- : Negative reference output
- SHLD : Connect to the shield that encloses lead wires and potentiometer. Do not connect to the chassis or "GND"
- PKUP : Not used
Connection for a strain gauge bridge
- REF+ : Positive reference output, connect to "top" of bridge
- SIG : Amplifier positive input, connect to bridge signal (+)
- REG- : Negative reference output, connect to "bottom" of bridge
- SHLD : Connect to the shield that encloses lead wires and bridge. Do not connect to the chassis or "GND"
- PKUP : Amplifier negative input, connect to bridge signal (-)
"POS-PWR" Power / signal header (5 pin)
- +12 : Connect to a low noise +12V power supply
- P+ : Positive going differential "Position" output
- GND : Connect to
- P- : Negative going differential "Position" output
- -12 : Connect to a low noise -12V power supply
NOTES:
- P+ and P- are connected to low impedance drive though a 50 ohm resistor
- Capacitance of 1.1uF (typical) is placed across P+ / P- which forms 1st order lowpass filter with Fc=1.45KHz
- P+ and P- are fully differential and are NOT ground referenced. For single ended operation, at the receiving end, connect P- to the local ground.
"Velocity" differentiated output header (2 pin)
- V+ : Positive going "Velocity" output
- v- : Negative going "Velocity" output
NOTES: See preceding notes for P+/P-