Difference between revisions of "POT4"
From DIDEAS Wiki
m (→ POT4 Power Supply) |
|||
(41 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
[[Medialab Documentation | Documentation HOME]] | [[Medialab Documentation | Documentation HOME]] | ||
− | ==assembly | + | |
+ | Also see : [[POT4a]] and [[POT4b]] | ||
+ | |||
+ | ==[[pot4 power supply | POT4 Power Supply]]== | ||
+ | |||
+ | ==[[POT4_PINOUT | POT4 Header Pinouts]]== | ||
+ | |||
+ | ==Voltage Reference== | ||
+ | |||
+ | Discussion of the [[POT2 Reference | voltage reference]]. | ||
+ | |||
+ | == Identification == | ||
+ | [[image:pot4_s1.jpg|right|thumb|160px|POT4]] | ||
+ | [[image:Rpot4-pcb-top-rev0-031505.png|right|thumb|80px|top side]] | ||
+ | [[image:Rpot4-pcb-bot-rev0-031505.png|right|thumb|80px|bottom side]] | ||
+ | |||
+ | *POT4 is a green PCB with white silk screen. | ||
+ | *Dimensions 1.75" x 0.85" | ||
+ | *Two mounting holes (diameter = 0.125"), top side clearance > 0.25" | ||
+ | *The color of DL1,DL2 indicates the input configuration of the board | ||
+ | <br><p><br> | ||
+ | |||
+ | ==Led Indicators== | ||
+ | *(DL1, DL2) : A pair of single LEDs indicate the present of power. These LEDs are aligned with the power input to the boards. | ||
+ | **RED : configured for potentiometer inputs (#1-2) | ||
+ | **GREEN : configured with bridge inputs (#3-8) | ||
+ | *DK1 : The intensity of this dual RED/GREEN LED indicates the voltage of the "position signal". | ||
+ | |||
+ | ==Jumpers== | ||
+ | * JF1 : 3 way jumper used to select source that drives that "Position" output. The signal source may be one of the following: | ||
+ | **Instrumentation amplifier output | ||
+ | **2nd order low pass filter output | ||
+ | **4th order low pass filter output | ||
+ | |||
+ | * JC1 : selects the "Shield" header signal source and is specified at assembly time. Signal sources include "GND", "COM", or "REF-". | ||
+ | |||
+ | |||
+ | ==Assembly Variations== | ||
POT4 can be built for either potentiometer input or bridge input. There are also [[POT4_options | several optional circuit modules]]. | POT4 can be built for either potentiometer input or bridge input. There are also [[POT4_options | several optional circuit modules]]. | ||
− | *boards #1, #2 : fully built with lowpass filters, differentiation | + | *Detailed [[POT4_GAINS | POT4 Gain by serial #]] |
− | *boards #3, #4 : minimally built for strain gauge bridge input | + | |
− | *[[Media:Pot4-for-strain-gauge-boards-5to8.pdf|boards #5 - #8]]: built for strain gauge bridge input and are minimally built with 2nd order LP filter | + | *boards #1, #2 : fully built with lowpass filters, differentiation and configured for potentiometer input. These boards use the [[Media:LT1167.pdf|LT1167]] with gain G=1+49.4K/RA1. |
+ | |||
+ | *boards #3, #4 : minimally built for strain gauge bridge input. These boards use the [[Media:Ina122.pdf|INA122]] with gain G=5+200K/RA1. Opamp LM324, 100K trim pot | ||
+ | |||
+ | *[[Media:Pot4-for-strain-gauge-boards-5to8.pdf|boards #5 - #8]]: built for strain gauge bridge input and are minimally built with 2nd order LP filter. These boards use the [[Media:Ina128.pdf|INA128]] with gain G=1+50K/RA1. Opamp LM324, "503" trim pot | ||
+ | |||
+ | * board #9 : same as #1,#2 with INA128, Gain 1+50K/RA1 - populated for POT board | ||
+ | *8-1-05 : board #9 returned for repairs. | ||
+ | |||
+ | ==Design Files== | ||
− | + | *[[Media:Pot4-sch-rev0-031505.pdf]] | |
+ | *[[Media:Rpot4-pcb-top-rev0-031505.pdf]] | ||
+ | *[[Media:Rpot4-pcb-bot-rev0-031505.pdf]] | ||
*[[Media:Pot4-for-strain-gauge-boards-5to8.pdf]] | *[[Media:Pot4-for-strain-gauge-boards-5to8.pdf]] | ||
− | + | ||
+ | ==FAQ== | ||
*Q: [[POT4_GAIN | How to adjust the gain?]] | *Q: [[POT4_GAIN | How to adjust the gain?]] | ||
*Q: [[POT4_PINOUT | What is pinout of the headers?]] | *Q: [[POT4_PINOUT | What is pinout of the headers?]] | ||
*Q: [[POTx_REFERENCE | What are the characteristics of the voltage reference?]] | *Q: [[POTx_REFERENCE | What are the characteristics of the voltage reference?]] | ||
+ | |||
+ | ==Bill of Materials== | ||
+ | |||
+ | [[POT4 Bill of Materials | Bill of Materials]] | ||
+ | |||
+ | ==Datasheets== | ||
+ | [[POT4 Datasheets]] |
Latest revision as of 20:22, 16 August 2006
Contents
POT4 Power Supply
POT4 Header Pinouts
Voltage Reference
Discussion of the voltage reference.
Identification
- POT4 is a green PCB with white silk screen.
- Dimensions 1.75" x 0.85"
- Two mounting holes (diameter = 0.125"), top side clearance > 0.25"
- The color of DL1,DL2 indicates the input configuration of the board
Led Indicators
- (DL1, DL2) : A pair of single LEDs indicate the present of power. These LEDs are aligned with the power input to the boards.
- RED : configured for potentiometer inputs (#1-2)
- GREEN : configured with bridge inputs (#3-8)
- DK1 : The intensity of this dual RED/GREEN LED indicates the voltage of the "position signal".
Jumpers
- JF1 : 3 way jumper used to select source that drives that "Position" output. The signal source may be one of the following:
- Instrumentation amplifier output
- 2nd order low pass filter output
- 4th order low pass filter output
- JC1 : selects the "Shield" header signal source and is specified at assembly time. Signal sources include "GND", "COM", or "REF-".
Assembly Variations
POT4 can be built for either potentiometer input or bridge input. There are also several optional circuit modules.
- Detailed POT4 Gain by serial #
- boards #1, #2 : fully built with lowpass filters, differentiation and configured for potentiometer input. These boards use the LT1167 with gain G=1+49.4K/RA1.
- boards #3, #4 : minimally built for strain gauge bridge input. These boards use the INA122 with gain G=5+200K/RA1. Opamp LM324, 100K trim pot
- boards #5 - #8: built for strain gauge bridge input and are minimally built with 2nd order LP filter. These boards use the INA128 with gain G=1+50K/RA1. Opamp LM324, "503" trim pot
- board #9 : same as #1,#2 with INA128, Gain 1+50K/RA1 - populated for POT board
- 8-1-05 : board #9 returned for repairs.
Design Files
- Media:Pot4-sch-rev0-031505.pdf
- Media:Rpot4-pcb-top-rev0-031505.pdf
- Media:Rpot4-pcb-bot-rev0-031505.pdf
- Media:Pot4-for-strain-gauge-boards-5to8.pdf
FAQ
- Q: How to adjust the gain?
- Q: What is pinout of the headers?
- Q: What are the characteristics of the voltage reference?