Difference between revisions of "Lifefix users"
From DIDEAS Wiki
m |
m |
||
Line 1: | Line 1: | ||
− | |||
− | |||
=safe startup= | =safe startup= | ||
* make sure copley is 'phased' and that the zero point is set | * make sure copley is 'phased' and that the zero point is set | ||
Line 10: | Line 8: | ||
* Test that the app will run (-n 0 = do zero passes) | * Test that the app will run (-n 0 = do zero passes) | ||
− | ** ./run_lifefix.py -i sw8 -c 0 -T 100 -F 1 -E 1 -n 0 -S | + | ** <strong>./run_lifefix.py -i sw8 -c 0 -T 100 -F 1 -E 1 -n 0 -S</strong> |
** ideally there will be no error messages and some matlab graphic output will appear | ** ideally there will be no error messages and some matlab graphic output will appear | ||
** if the swifi isn't working an error message will be output and the process stopped. | ** if the swifi isn't working an error message will be output and the process stopped. | ||
* Run the gentle cycle (-F 1) for 1 pass (-n 1) with 100N of AK output (-T 100): | * Run the gentle cycle (-F 1) for 1 pass (-n 1) with 100N of AK output (-T 100): | ||
− | ** ./run_lifefix.py -i sw8 -c 0 -T 100 -F 1 -E 1 -n 1 -S | + | ** <strong>./run_lifefix.py -i sw8 -c 0 -T 100 -F 1 -E 1 -n 1 -S</strong> |
* Run the full cycle (-F 0) for 1 pass (-n 1) with 100N of AK output (-T 100): | * Run the full cycle (-F 0) for 1 pass (-n 1) with 100N of AK output (-T 100): | ||
− | ** ./run_lifefix.py -i sw8 -c 0 -T 100 -F 0 -E 1 -n 1 -S | + | ** <strong>./run_lifefix.py -i sw8 -c 0 -T 100 -F 0 -E 1 -n 1 -S</strong> |
* Run the full cycle (-F 0) for 1 pass (-n 1) with 2000N full thrust (-T 2000): | * Run the full cycle (-F 0) for 1 pass (-n 1) with 2000N full thrust (-T 2000): | ||
− | ** ./run_lifefix.py -i sw8 -c 0 -T 100 -F 0 -E 1 -n 1 -S | + | ** <strong>./run_lifefix.py -i sw8 -c 0 -T 100 -F 0 -E 1 -n 1 -S</strong> |
==issues== | ==issues== | ||
*sometimes the SWIFI outputs garbage upon power up | *sometimes the SWIFI outputs garbage upon power up |
Revision as of 22:23, 10 October 2009
safe startup
- make sure copley is 'phased' and that the zero point is set
- power the AK, wait for the high pitch 'beep beep'
- if a there is a low humm, then likely the commutation failed. The AK will retry. Hand adjust the back drive screw between attempts to help.
- ideally be running the matlab plotter on CB's machine
- Test that the app will run (-n 0 = do zero passes)
- ./run_lifefix.py -i sw8 -c 0 -T 100 -F 1 -E 1 -n 0 -S
- ideally there will be no error messages and some matlab graphic output will appear
- if the swifi isn't working an error message will be output and the process stopped.
- Run the gentle cycle (-F 1) for 1 pass (-n 1) with 100N of AK output (-T 100):
- ./run_lifefix.py -i sw8 -c 0 -T 100 -F 1 -E 1 -n 1 -S
- Run the full cycle (-F 0) for 1 pass (-n 1) with 100N of AK output (-T 100):
- ./run_lifefix.py -i sw8 -c 0 -T 100 -F 0 -E 1 -n 1 -S
- Run the full cycle (-F 0) for 1 pass (-n 1) with 2000N full thrust (-T 2000):
- ./run_lifefix.py -i sw8 -c 0 -T 100 -F 0 -E 1 -n 1 -S
issues
- sometimes the SWIFI outputs garbage upon power up