Difference between revisions of "Lifefix users"
From DIDEAS Wiki
m |
m |
||
| Line 1: | Line 1: | ||
| + | {{pf_top_nav}} | ||
| + | {{T_Lifefix}} | ||
| + | {{T_lf_tests}} | ||
| + | |||
=safe startup= | =safe startup= | ||
* make sure copley is 'phased' and that the zero point is set | * make sure copley is 'phased' and that the zero point is set | ||
Revision as of 04:16, 12 October 2009
PF Users Navigation:
- PCB; Lifefix_users; Pf_users; benchtest_users; CalibFix Users; Hardware; Assembly ; iochan ;
- PCA : PCB ; AKENC SC/MC 218 ; FET 217 ; IMU219 ; Swifi ; Rev200_mods ; PCA Inventory
- Special Commands to the Ankle (PFCMD) : State Controller Commands; Motor Controller Commands; Python Examples; IMU Commands ;PFCMD_PY; Pf_calb_table_py; Virtual spring test; PF EEPROM
- DOC: Pf_users; Powerfoot Keyboard User Interface; Steps for Manual Tuning; "Dashboard" Program For Assisting with Tuning
- NEW (CEB) WIKI
- Torque Feedback Controller Guide
- LF: Lifefix_users; Ltf_science; lifefix_log ; Loadwasher ; Lifefix;
- TESTS: LF_TEST100; LF_TEST_101; LF_TEST102; LF_TEST_103; LF_TEST_104
safe startup
- make sure copley is 'phased' and that the zero point is set
- power the AK, wait for the high pitch 'beep beep'
- if a there is a low humm, then likely the commutation failed. The AK will retry. Hand adjust the back drive screw between attempts to help.
- ideally be running the matlab plotter on CB's machine
- Test that the app will run (-n 0 = do zero passes)
- ./run_lifefix.py -i sw8 -c 0 -T 100 -F 1 -E 1 -n 0 -S
- ideally there will be no error messages and some matlab graphic output will appear
- if the swifi isn't working an error message will be output and the process stopped.
- Run the gentle cycle (-F 1) for 1 pass (-n 1) with 100N of AK output (-T 100):
- ./run_lifefix.py -i sw8 -c 0 -T 100 -F 1 -E 1 -n 1 -S
- there should be no python errors, however there will be an envelope error
- Run the full cycle (-F 0) for 1 pass (-n 1) with 100N of AK output (-T 100):
- ./run_lifefix.py -i sw8 -c 0 -T 100 -F 0 -E 1 -n 1 -S
- there should be no python errors, however there will be an envelope error
- Run the full cycle (-F 0) for 1 pass (-n 1) with 2000N full thrust (-T 2000):
- ./run_lifefix.py -i sw8 -c 0 -T 2000 -F 0 -E 1 -n 1 -S
- there should be no python errors, and no envelope errors.
- proceed with a short run (100 passes) to verify operation
- ./run_lifefix.py -i sw8 -c 0 -T 2000 -F 0 -E 1 -n 100 -S
issues
- if matlab w/plot_float is not running CB's PC there will be an error
- sometimes the SWIFI outputs garbage upon power up
- the lifefix program is now testing for valid SWIFI output.
