Difference between revisions of "Lifefix log"
From DIDEAS Wiki
m |
m (→LF #1 LOG) |
||
Line 3: | Line 3: | ||
=LF #1 LOG= | =LF #1 LOG= | ||
+ | |||
+ | *09-09-17 04:30 - started 7200 passes | ||
+ | *09-09-17 03:30 - ran a few hundred cycles during experiments. | ||
+ | *09-09-17 03:00 - 3 incidences of max plantarflexion, and rephased the motor current | ||
+ | |||
*09-09-11 23:53 - stops after 4969 passes due to belt break, ball nut on floor, load washer hanging | *09-09-11 23:53 - stops after 4969 passes due to belt break, ball nut on floor, load washer hanging | ||
*09-09-11 21:00 - started LF_TEST_101 | *09-09-11 21:00 - started LF_TEST_101 | ||
Line 13: | Line 18: | ||
*09-09-10 20:00 - resonance experiments of inside only - excessive dorsiflexion | *09-09-10 20:00 - resonance experiments of inside only - excessive dorsiflexion | ||
*09-09-10 16:00 - resonance experiments of full LF w/Kristin | *09-09-10 16:00 - resonance experiments of full LF w/Kristin | ||
− | |||
=LF_TEST_101= | =LF_TEST_101= |
Revision as of 08:38, 17 September 2009
PF Users Navigation:
- PCB; Lifefix_users; Pf_users; benchtest_users; CalibFix Users; Hardware; Assembly ; iochan ;
- PCA : PCB ; AKENC SC/MC 218 ; FET 217 ; IMU219 ; Swifi ; Rev200_mods ; PCA Inventory
- Special Commands to the Ankle (PFCMD) : State Controller Commands; Motor Controller Commands; Python Examples; IMU Commands ;PFCMD_PY; Pf_calb_table_py; Virtual spring test; PF EEPROM
- DOC: Pf_users; Powerfoot Keyboard User Interface; Steps for Manual Tuning; "Dashboard" Program For Assisting with Tuning
- NEW (CEB) WIKI
- Torque Feedback Controller Guide
LF #1 LOG
- 09-09-17 04:30 - started 7200 passes
- 09-09-17 03:30 - ran a few hundred cycles during experiments.
- 09-09-17 03:00 - 3 incidences of max plantarflexion, and rephased the motor current
- 09-09-11 23:53 - stops after 4969 passes due to belt break, ball nut on floor, load washer hanging
- 09-09-11 21:00 - started LF_TEST_101
- 09-09-11 14:00 - loadwasher tightened
- 09-09-11 03:00 - notice that LW has slipped - is no longer pre-loaded.
- 09-09-11 00:10 - during belt stress test, LF runs away and max plantarflexes
- 09-09-10 23:30 - replaced broken belt; three ball screw balls fall out (from yesterday's over extension)
- 09-09-10 02:30 - stopped due to broken belt (3600 cycles)
- 09-09-10 00:30 - started LF_TEST100
- 09-09-10 20:00 - resonance experiments of inside only - excessive dorsiflexion
- 09-09-10 16:00 - resonance experiments of full LF w/Kristin
LF_TEST_101
- appx 29 cyc per min
- has belt thresh
- full amplitude on drive motor
- thrust scale=3000N
LF_TEST_100
- appx 30 cyc per min
- full amplitude on drive motor
- thrust scale=3000N