Difference between revisions of "COPMM1"
From DIDEAS Wiki
m |
m |
||
Line 32: | Line 32: | ||
*[http://en.wikipedia.org/wiki/Help:Table WIKI TABLE HELP] | *[http://en.wikipedia.org/wiki/Help:Table WIKI TABLE HELP] | ||
− | {| border="1" cellpadding="12" | + | {| border="1" cellpadding="12" width="100%" |
|+COPMM1 REV0 (6-6-05) | |+COPMM1 REV0 (6-6-05) | ||
|- | |- | ||
− | !width="5%"| NUM ||width="10%" | REFDES || width="15%"|Part# || width=" | + | !width="5%"| NUM ||width="10%" | REFDES || width="15%"|Part# || width="20%"|Desc || width="10%"|Source || width="10%"|Price || width="30%"|Notes |
|- | |- | ||
| 1 || PP1 & PM1 || 277-1226-ND || 7 pos 3.81mm header || DIG || 2.11 || probably ok to use a 4 position header centered | | 1 || PP1 & PM1 || 277-1226-ND || 7 pos 3.81mm header || DIG || 2.11 || probably ok to use a 4 position header centered |
Revision as of 06:41, 10 June 2005
Breakout board for Accelnet Micro Module
- for Copley Controls Corp models : ACK-055-06, or ACK-090-04
Identification
- yellow tint PCB from AP-Circuits
- bottom side text label "medialab/copmm1.pcb", "06/06/05"
- dimensions : 3.36 x 2.21"
Designs
Reference
future revisions
- change LED to gull-wing such as P504-ND
history
- Board submitted to AP-Circuits 6-8-05
- Ser #1,#2 built 6-10-05
Bill of Materials
NUM | REFDES | Part# | Desc | Source | Price | Notes |
---|---|---|---|---|---|---|
1 | PP1 & PM1 | 277-1226-ND | 7 pos 3.81mm header | DIG | 2.11 | probably ok to use a 4 position header centered
277-1223-ND (4 pos header) |
1 | PP1 & PM1 | 277-1181-ND | 7 pos 3.81 plug / mate for above header | DIG | 6.54 | ALT : 277-1178-ND (4 pos plug)) |
1 | M1-a | SSW-111-01-S-D | 22 pos female header / socket strip 0.1 | Samtec | ? | ALT : 929975-01-36-ND (DIG) possible |
1 | M1-b | SSW-117-01-S-D | 34 pos female header / socket strip 0.1 | Samtec | ? | ALT : 929975-01-36-ND (DIG) possible |
1 | LD1 | 445-1746-1-ND | NLV25T (56uH) EIA1008 | DIG | 0.28 | |
1 | CD1 | 399-1551-1-ND | 6.3V tant 3216 (size A) 10uF | DIG | 0.18 | requirements : Size A tant, >=1uF, >=6.3V |
1 | PR1 | A9031-ND | PCB mount RJ-45 | DIG | 0.83 | |
1 | PD1 | 182-25F-ND | DB25F right angle | DIG | 2.23 | ALT : 182-825F-ND DB25F w/screw tabs |
1 | RP1 | RHM9.10KFCT-ND | 9.2k EIA1206 | DIG | 0.047 | Adjust resistance based on HV power supply :
R = (Vhv - 2V) / 5mA |
1 | RD1 | RHM510CCT-ND | 510 ohm EIA0805 | DIG | 0.038 | |
2 | DP1, DD1 | P301-ND | 5mm 0.1 red led | DIG | 0.168 | generic 3 or 5mm 0.1 lead space |
2 | DM1, DM3 | MMSD4148T1 | 100V sod-123 diode | DIG | 0.18 | ALT : MMSD914T1 |
1 | DM2 | P507CT-ND | dual red/green gull wing LED | DIG | 0.75 | |
1 | RM1 | RHM4.64KFCT-ND | 4.6K RES1206 | DIG | 0.047 | Adjust resistance based on HV power supply : R=(Vhv - 2V) / 10mA |
3 | CP1-3 | P10343-ND | 100u, 63V (FC series) 10mm x 12.5mm | DIG | 0.28 | ALT : P5194-ND (220u 63V M series) For 48V motor voltage adjust cap to For higher supply use 100V cap |