Difference between revisions of "Upright"
From DIDEAS Wiki
m |
m (→UPSG1) |
||
Line 13: | Line 13: | ||
=UPSG1= | =UPSG1= | ||
*U1-U3 populated with 4.096V reference, X60003CIG3Z-41T1CT-ND | *U1-U3 populated with 4.096V reference, X60003CIG3Z-41T1CT-ND | ||
+ | *Jumper wire between PO1.1 and PO1.9. This bridge the SG.REF signal that didn't get routed | ||
+ | *The PCB has two 1K resistors (1st and 2nd) that bridge REF+- to S+. | ||
+ | *350 ohm resistor across PO1.12 and PO1.11. This resistor (3rd) bridges REF- and SG-. | ||
+ | *The 4th bridge resistor connects REF+ and SG- | ||
=[http://scripts.mit.edu/~biomechatronics/wiki/index.php?title=BLMD6C BLMD6C]= | =[http://scripts.mit.edu/~biomechatronics/wiki/index.php?title=BLMD6C BLMD6C]= |
Revision as of 01:50, 26 July 2008
Contents
Sensors
- Hall sensor : AN12 -> PB12 -> adc_0
- SG1 (torque) -> SG channel 1 (2.0k, 500x) -> PB0 -> adc_1
- SG2 (compression) -> SG channel 2 (8.2k, 122x) -> PB1 -> adc_2
- SG3 (series spring) -> SG channel 3 (5.9k, 170x) -> PB2 -> adc_3
- INA326 gain : 2 * R2/R1 = (2 * 500k/xx)
AKCPU2Z Modifications
- verify JR1 is in position in 2-3
- change RB1 from 470 ohm to 0.0 ohms. - this is to power the strain adapter board
UPSG1
- U1-U3 populated with 4.096V reference, X60003CIG3Z-41T1CT-ND
- Jumper wire between PO1.1 and PO1.9. This bridge the SG.REF signal that didn't get routed
- The PCB has two 1K resistors (1st and 2nd) that bridge REF+- to S+.
- 350 ohm resistor across PO1.12 and PO1.11. This resistor (3rd) bridges REF- and SG-.
- The 4th bridge resistor connects REF+ and SG-
BLMD6C
- more details for uprights here.
Software Modifications
- QEI changed from 4x to 2x mode as:
- 1) encoder has higher resolution
- 2) gear ratio is higher.
- even in 2x mode, max planterflexion results in count of -27k, close to limit of -32k
- qei.c modified to support both 2x and 4x modes, qei.c needs ankle consts.
- timer3.c modified to change sign of motor encoder.
- statemachine.c modified to not have initial dosaflexion
assembly revisions
BLFT6C
- I3, I4 : installed zener to protect ADC when temp sensor is absent.
BLMD6C
- I3 : replaced RX1,RX2 each with a 3.0 ohm in parallel with 4.7 ohm in 0805 packet. Existing 2ohm-0603 failed periodically.
dataport
packet
- 2 bytes sync
- 2 bytes field widths (several fields with a byte total 'n')
- 1+n bytes of data