Difference between revisions of "POT4a"
From DIDEAS Wiki
m |
m |
||
| Line 1: | Line 1: | ||
Also see : [[POT4]] amd [[POT4b]] | Also see : [[POT4]] amd [[POT4b]] | ||
| + | |||
| + | |||
| + | |||
| + | ==Revisions from POT4== | ||
| + | *add 5pin, 1.25mm header for strain gague | ||
| + | *removed unused input resistors and capacitors | ||
| + | *On POT4 a 1meg resistor was stacked on CC3 - this resistor added to SCH and PCB | ||
| + | *removed 4th order filter, changed 3way jumper to 2way | ||
| + | *2nd order filter is now NON-Inverting | ||
| + | *input cable shield can be connected to COM via 0603 resistor | ||
| + | *changed PCB pattern for output driver caps to CAP200-SQ (acurately represents compoent shape) | ||
| + | *changed 0805 output cable CAP to 1206. Panasonic X5R series @ 25V 1uf to 10uF! | ||
| + | *added 10 turn POT for variable gain (optional) | ||
| + | *change CD2 (0.1u in derivative circuit) to 1206 size (was 0805) | ||
| + | |||
==Power Supply== | ==Power Supply== | ||
| Line 23: | Line 38: | ||
==Design Files== | ==Design Files== | ||
| − | |||
*[[Media:Pot4a-sch-reva-062205.pdf]] | *[[Media:Pot4a-sch-reva-062205.pdf]] | ||
*[[Media:Rpot4a-pcb-top-reva-061605.pdf]] | *[[Media:Rpot4a-pcb-top-reva-061605.pdf]] | ||
*[[Media:Rpot4a-pcb-bot-reva-061605.pdf]] | *[[Media:Rpot4a-pcb-bot-reva-061605.pdf]] | ||
| − | + | *[[Media:Pot4a-revb-gerber-tango-061606.zip Gerber files and Tango DOS source (6-16-05)]] | |
| − | |||
| − | |||
| − | * | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Revision as of 20:08, 22 June 2005
Revisions from POT4
- add 5pin, 1.25mm header for strain gague
- removed unused input resistors and capacitors
- On POT4 a 1meg resistor was stacked on CC3 - this resistor added to SCH and PCB
- removed 4th order filter, changed 3way jumper to 2way
- 2nd order filter is now NON-Inverting
- input cable shield can be connected to COM via 0603 resistor
- changed PCB pattern for output driver caps to CAP200-SQ (acurately represents compoent shape)
- changed 0805 output cable CAP to 1206. Panasonic X5R series @ 25V 1uf to 10uF!
- added 10 turn POT for variable gain (optional)
- change CD2 (0.1u in derivative circuit) to 1206 size (was 0805)
Power Supply
- +12V, GND, -12V recommend
- Supply current < 50mA (20mA typical)
- Maximum supply voltage is +-15V
Identification
- POT4a is a green PCB with white silk screen on two sides.
- Dimensions 1.75" x 0.85"
- Two mounting holes (diameter = 0.125"), top side clearance > 0.25"
- The color of DL1,DL2 indicates the input configuration of the board
Led Indicators
- (DL1, DL2) : A pair of single LEDs indicate the present of power. These LEDs are aligned with the power input to the boards.
- DK1 : The intensity of this dual RED/GREEN LED indicates the voltage of the "position signal".
