Difference between revisions of "JANK1"
From DIDEAS Wiki
m |
m (→bill of materials) |
||
| Line 26: | Line 26: | ||
1 PA1 WM-4207-ND 9 pin molex header | 1 PA1 WM-4207-ND 9 pin molex header | ||
1 PD2 WM-4208-ND 10 pin molex header | 1 PD2 WM-4208-ND 10 pin molex header | ||
| − | 2 PO1, PC1 MHB16K-ND 2x8 header | + | 2 PO1, PC1 MHB16K-ND 2x8 ribbon header |
| − | 2 PA2, PB1 MHB14K-ND 2x7 header | + | 2 PA2, PB1 MHB14K-ND 2x7 ribbon header |
| − | 1 PB2 MHB10K-ND 2x5 header | + | 1 PB2 MHB10K-ND 2x5 ribbon header |
| − | 2 PS1, PM2 MHB50K-ND 2x25 header | + | 2 PS1, PM2 MHB50K-ND 2x25 ribbon header |
| − | 1 PS2 MHB40K-ND 2x20 header | + | 1 PS2 MHB40K-ND 2x20 ribbon header |
1 JP1 *ZZ1 2x4 pin jumper block | 1 JP1 *ZZ1 2x4 pin jumper block | ||
1 J1 *ZZ1 2x5 pin jumper block | 1 J1 *ZZ1 2x5 pin jumper block | ||
| Line 40: | Line 40: | ||
*ZZ1 build from : A26525-40-ND 2x40 pos unshrouded breaker headers | *ZZ1 build from : A26525-40-ND 2x40 pos unshrouded breaker headers | ||
| + | |||
| + | |||
| + | PO1, PC1 mate with MKC16K-ND (socket connector) and ribbon cable MC16G | ||
| + | ribbon cable length 6 feet : from backpack to ankle | ||
| + | |||
| + | PA2, PB1 : mate with MKC14K-ND & ribbon cable MC14G (6 ft) | ||
| + | |||
| + | PB2 : mates with MKC10K-ND & ribbon cable MC10G (6 ft) | ||
| + | |||
| + | PS1, PM2 : mates with MKC50K-ND & ribbon cable MC50G | ||
| + | these cables connect JANK1 to Sensoray and Diamond MM32 boards (3 to 4 inches) | ||
| + | |||
| + | PS2 : mates with MKC40K-ND & ribbon cable MC40G | ||
| + | connects to Sensoray board ~3 inches | ||
| + | |||
| + | molex headers mate with: | ||
| + | A30994-ND : 2 pin, 28 AWG green receptacle (closed end with lock without polarizing tabs) | ||
| + | A30995-ND : 3 pin, 28 AWG green | ||
| + | A30986-ND : 2 pin, 26 AWG blue | ||
| + | A30978-ND : 2 pin, 24 AWG white | ||
| + | A31080-ND : 2 pin, 22 AWG red | ||
Revision as of 09:35, 14 September 2006
JANK1: (Jeff Ankle PC-104/Maxon controller interface )
Part of the Ankle_0806 project:
JANK1 | BENCH2 | BENCH2F | BATPTC1 | BATMRG1 | BATPWR1 | POT4a | QAKAMP
identification
- labeled "ankle-v3/jank1.pcb", "082506/091006"
- 3.8 x 3.6" inch APCircuits PCB
design files
bill of materials
Quan RefDes Part # (dig) description 2 PP2 WM-4200-ND 2 pin molex header 6 PP1 PD1, PP3-PP8 WM-4201-ND 3 pin molex header 1 PM1 WM-4205-ND 7 pin molex header 1 PA1 WM-4207-ND 9 pin molex header 1 PD2 WM-4208-ND 10 pin molex header 2 PO1, PC1 MHB16K-ND 2x8 ribbon header 2 PA2, PB1 MHB14K-ND 2x7 ribbon header 1 PB2 MHB10K-ND 2x5 ribbon header 2 PS1, PM2 MHB50K-ND 2x25 ribbon header 1 PS2 MHB40K-ND 2x20 ribbon header 1 JP1 *ZZ1 2x4 pin jumper block 1 J1 *ZZ1 2x5 pin jumper block 3 RL1,3,5 RHM1.0KCCT-ND 1K 0805 1% resistors 2 RL2,4 RHM402CCT-ND 402 ohm 0805 1% res 1 RL6 RHM4.99KCCT-ND 4.99k 0805 1% res 3 DL1,2,3 P507CT-ND dual red/green SMT led
*ZZ1 build from : A26525-40-ND 2x40 pos unshrouded breaker headers
PO1, PC1 mate with MKC16K-ND (socket connector) and ribbon cable MC16G ribbon cable length 6 feet : from backpack to ankle
PA2, PB1 : mate with MKC14K-ND & ribbon cable MC14G (6 ft)
PB2 : mates with MKC10K-ND & ribbon cable MC10G (6 ft)
PS1, PM2 : mates with MKC50K-ND & ribbon cable MC50G these cables connect JANK1 to Sensoray and Diamond MM32 boards (3 to 4 inches)
PS2 : mates with MKC40K-ND & ribbon cable MC40G connects to Sensoray board ~3 inches molex headers mate with: A30994-ND : 2 pin, 28 AWG green receptacle (closed end with lock without polarizing tabs) A30995-ND : 3 pin, 28 AWG green A30986-ND : 2 pin, 26 AWG blue A30978-ND : 2 pin, 24 AWG white A31080-ND : 2 pin, 22 AWG red
